If, for some reason, such as an adjustment in the system's time-of-day clock or the addition of a leap second, the current interval exceeds the maximum value, the agent will return the maximum value. An entry in the hdsl2ShdslEndpointConfTable. The current loop attenuation for this endpoint as reported in a Network or Customer Side Performance Status message. A counter associated with interface performance measurements during the most previous 1-day 24 hour measurement interval. Following the 5 second period, the agent will restore the object to the 'ready 1 ' state. Getting Started Knowledge Base Help.
| Uploader: | Goltira |
| Date Added: | 28 March 2008 |
| File Size: | 66.81 Mb |
| Operating Systems: | Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X |
| Downloads: | 50089 |
| Price: | Free* [*Free Regsitration Required] |
If, for some reason, such as an adjustment in the system's time-of-day clock or the addition of a leap second, the current interval exceeds the maximum value, the agent will return the maximum value. The various bit positions are as follows: This object configures the loop attenuation alarm threshold.
Each entry corresponds to a single alarm configuration profile. Interval 1 is the most recent previous hdsl2-shdls-line-mib interval 30 is 30 days ago. A gauge associated with interface performance measurements in a current 1-day 24 hour measurement interval. The various bit positions are as follows: Each entry contains status and performance information relating to a single segment endpoint.
HDSL2-SHDSL-LINE-MIB
This notification indicates impending unit failure due to loss of local power last gasp. The default value of this object is hdsl2-shdsl-line-min zero-length SnmpAdminString.
hdsl2-shdsl-line-miib When Line Probe is enabled, the system performs Line Probing to find the best possible rate. Other vendor information as reported in an Inventory Response message.
HDSL2-SHDSL-LINE-MIB
An entry in the hdsl2ShdslEndpointCurrTable. If the minimum line rate equals the maximum line rate hdsl2ShdslSpanMaxLineRatethe line rate is considered 'fixed'. History Data Interval number. An agent may reside at either end of the line; however, the MIB module is designed to require no management communication between the modems beyond that inherent in the low-level EOC line protocol as defined in Hdsl2-shdsl-linemib T1E1.
Please note that zero is a valid value. Updated conformance statements as necessary.
August 28, Following the 5 second period, the agent will restore the object to the 'ready 1 ' state. The value of this gauge is equal to the value of the current day gauge, as defined in a companion object of type Hdsl2ShdslPerfCurrDayCount, at the end of its most recent interval. This object configures the threshold for the number of Unavailable Seconds UAS within any given minute performance data collection interval. The values are obtained from the alarm configuration profile referenced by this object.
Any attempt to set this object to a value that is not the value of the index for an active entry in the profile table, hdsl2ShdslSpanConfProfileTable, MUST be rejected.
An agent may reside at either end of the line; however, the MIB module is designed to require no management communication between the modems beyond that inherent in the low-level EOC line protocol as defined in ANSI T1E1. An entry in the hdsl2Shdsl15MinIntervalTable.
HDSL2-SHDSL-LINE-MIB | IPHost Network Monitor
This notification indicates that the bit setting for dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed. This object provides the maximum rate the line is capable of achieving. Count of CRC anomalies on this endpoint since the xU was last restarted. This is intended to supplement ifOperStatus.
Added an object to indicate whether the tip and ring are reversed on a wire pair. The alarm threshold configuration Added display hints to textual conventions as necessary.
This notification indicates that the bit setting for protocolInitFailure in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed. If, for some reason, such as an adjustment in the system's time-of-day clock or the addition of a leap second, the current interval exceeds the maximum value, the agent will return the maximum value.
For minute intervals, the range is limited to Vendor ID as reported in an Inventory Response message.
No comments:
Post a Comment